#Mweb adsl router settings how to#
#Mweb adsl router settings password#

#Mweb adsl router settings password#

If your router cannot handle the length of password we provide, please contact support who will be happy to set a shorter password. If you change the password on our system your lines will go off line until you change the password on the router as well. We allocate a password, but you can change this on the Broadband Control Pages. Leave untagged, no VLAN, and connect your router to the Openreach ONT Typically you'll have a PPPoE capable router and will connect the WAN port to the Openreach ONT that was installed by Openreach. Use this if your router has a built in VDSL modem. (Not applicable if you are using the Openreach modem). Some customers may have a separate Openreach modem, and will then use a PPPoE router. Typically you'll have a FTTC capable router (ie a router with a built in FTTC/VDSL modem) and will use PPPoE, and you'll need to set a VLAN in the PPPoE settings. For FTTC and FTTP the only operational mode is PPPoE directly with RFC4638 support allowing 1500 byte MTU. In such cases you need the LLC-Mux normally. This can be useful when using a bridging modem. Please note that most DSL lines (BT and TT) do allow PPPoE mode.

You may want your DSL router to act as a DHCP server for your LAN. If you have a separate router/firewall link block, you will need to configure a static route for your main IP block via your router/firewall. DO NOT make up a netmask for use with a real IP address that we have allocated - always use the one we have advised. If you have a block of IPs from us, use the IP and netmask as advised. If using NAT then this will be some default such as 192.168.1.254. This will change depending on equipment at our end and may even change on every connection in the future. The IP address for our end of the PPP link should not be configured. If you configure this incorrectly you will normally find you cannot log in at all. Whilst we allocate a fixed IP address for your service, including the WAN address, it is best not to set this as it is allocated automatically using PPP. We allocate a password, but you can change this on the Broadband Control Pages. 1, 2, etc.) for where customers have multiple lines sharing IP addresses. The final number is the line number (e.g. This is of the form of a name followed by a realm, a dot then a single digit number. We allocate a login for one or more lines. This is often the default on most broadband routers PPPoE (see below) is more commonly used when bridging to a separate PPPoE device such as a FireBrick When routing IP you want your router to connect using PPPoA mode. This means that IP traffic is routed, and is the normal mode unless setting up a PPPoE bridge to another device. Usually set this to automatic as it allows ADSL or ADSL2+ (depending on modem and line type). Once restarted, the router should connect automatically.ADSL: Basic BT and TT PPPoA Settings Setting On the final page click Restart to save your settings and restart the router. Here enter your Zen username and connection password (please refer to the Technical Details email you received when you joined Zen), then click Next. Once done, the settings for VPI, VCI and Connection Type should automatically populate with the correct settings. Once you have typed in the new password twice click Next. You will be asked to change the router login password from the default of admin. The web page will then dispaly the basic settings page for the D-Link router, click the Setup Wizard button to begin the ADSL setup process. You will be prompted for the default login settings: Once you have connected the device to the telephone line and your local network via an ethernet cable, browse to

#Mweb adsl router settings how to#

The following guide shows you how to connect your equipment:

If you experience problems when using this device please ensure you have entered the correct settings as detailed below and consult D-Link for further assistance.Įnsure your Broadband equipment is set up correctly. NOTE: This device is not supplied by or supported by Zen Internet. This router automatically detects whether to connect using ADSL or ADSL2+, there is no option to override this. If you are unable to locate the CD, follow the guidelines below. If you have the CD that came with the router, run the setup program. This guide has been written to assist users configuring a DLink DSL-2740B for the first time to allow access to the Internet.